Starting work on my BX

All aspects of tuning,modification and repairs to the BX 16valve.
Post Reply
nigel
Tick Over
Posts: 16
Joined: Wed Jul 14, 2010 12:24 pm
Location: Australia

Starting work on my BX

Post by nigel »

Hi all,

As some know Ive recently aquired a 1989 BX16V.

Ive just ordered a Valeo Clutch kit + various seals from a local French car Citroen specialist who is a guru and knows his stuff. Hes very genrous with his time and advice and was happy to explain some minor height corrector issues I had. Anyway talk turned to motor oil and he recommended Elf Competiton 10W40. http://www.elfoil.com.au/products/produ ... _SM_10W-40

He scoffed at me when I told him that Ive used Castrol oils on all my other cars. Said that the 16V has a high performance engine and that the elf stuff was up to the task. Took that to also mean that the Castrol stuff wont cut it. So Im looking at 2.5 times more money for oil (Castrol lube guide recommends GTX 3) which Im happy to accept if its better for my engine.

Anyway Im just so excited to have this car. Its a real performance car. So hopefully get the clutch in soon, sought out some minor electrics issues and get this baby motoring.

Gave it a wash and a very basic polish as I couldnt bare to look at its sad whethered paintwork.

Image

Image

Image
User avatar
Adrian E
Moderator
Posts: 569
Joined: Wed Jul 12, 2006 10:09 pm
Location: Surrey, UK

Post by Adrian E »

Haven't looked in detail at the oil specs, but whatever you do don't get sucked into using a fully synthetic oil in an engine as old as this - all you'll do is increase your oil consumption and potentially knacker the bearings.

A good quality semi-synthetic is by far and away the best choice for these engines, especially as they require pretty frequent changes.
User avatar
Kitch
5000 rpm
Posts: 737
Joined: Sun Aug 06, 2006 12:52 pm

Post by Kitch »

Adrian E wrote:Haven't looked in detail at the oil specs, but whatever you do don't get sucked into using a fully synthetic oil in an engine as old as this - all you'll do is increase your oil consumption and potentially knacker the bearings.

A good quality semi-synthetic is by far and away the best choice for these engines, especially as they require pretty frequent changes.
What's being fully synthetic got to do with engine wear? :? If anything, fully-syn retains it's viscosity (sp) over harder conditions than semi....of course it will, it's designed to. If fully was around when these cars were designed, they'd have it from new. Thats my opinion anyway.

Mine's running (and has been for around 3 years) on fully synthetic.
User avatar
Adrian E
Moderator
Posts: 569
Joined: Wed Jul 12, 2006 10:09 pm
Location: Surrey, UK

Post by Adrian E »

Kitch

....but I bet yours is at least running the correct grade? It's extremely difficult to get the correct grade in a fully synth, so MOST people that run fully synth opt for what they can get, which is usually a 0wsomething rated oil, which is too thin for the tolerances on the engine hence the risk of doing bearing damage, or they opt for a 15w60 which then gives you too much oil pressure when cold and it pee's out all over the place and can potentially cause problems if given too many beans from cold.

The 16V had 6,000 mile service intervals from new - if the oil is changed annually/every 6k then you won't notice a difference as the oil takes longer than that to degrade - you are quite correct that if the oil was in there for 20k/2 years like on a modern car then you need it to retain its properties for longer.

I'm sure you're right about if fully synth was available then it would be spec'd, but they would have needed to use different manufacturing tolerances in the engine to allow its use.

I used to hunt high and low for the correct grade of Castrol RS (they did 2 types) but I got sick of spending over £70 on an oil change every 6 months - personally I don't think it's necessary or value for money. The car ran better when I went back to semi-synth as well.
User avatar
docchevron1472
4000 rpm
Posts: 336
Joined: Tue Aug 22, 2006 10:53 am
Location: The End of the World
Contact:

Post by docchevron1472 »

I use Total Quartz 7000 10/40 semi in mine, always have bar the initial oil I put in post rebuild which was a straight mineral..
That said I dump it every 3K miles / 3 months regardless..
Last edited by docchevron1472 on Thu Aug 05, 2010 12:26 pm, edited 1 time in total.
1990 BX 16v Phase 2
1989 BX TD hybrid
1971 BL 350FG Ambulance (unique)
1993 Dennis Lance 132
That's when I reach for my Revolver
ed_straker
3000 rpm
Posts: 169
Joined: Thu Aug 03, 2006 7:28 am
Location: germany...don't mention the war!

Post by ed_straker »

I used some whatsitsname 10W40 semi-synthetic. I guess everything from today is much better than what they used back in the 80s.
Honda Civic Type S
User avatar
Simran
4000 rpm
Posts: 424
Joined: Sat Aug 12, 2006 12:30 am
Location: leicester

Post by Simran »

Nigel, your car looks so good cleaned up, a clean set of standard alloys always does wonders for these, the shiny lip makes the car look brand new!

I agree with what Kitch mentioned in another post, moving the fans and the rad out the way makes getting at the pipes so much easier. You dont have to remove the radiator though so it can stay connected, if you take the fans out, the rad will lean back enough to give you decent working space....unless you have air con, that is :lol:
User avatar
Kitch
5000 rpm
Posts: 737
Joined: Sun Aug 06, 2006 12:52 pm

Post by Kitch »

Motul 10w40 in mine, yeah. Although 5w40 really wouldn't make a massive difference as the grade only really differs below normal operation temperature. I used 5w40 with no noticable difference to oil pressure or running. Agree that going 0w40 will not protect the engine when it's cold too. I used to use 10W60 Castrol RS and the car ran beautifully, but I do wonder if it contributed to my oil surge meltdown all those years ago.

Being that the service interval is 6000miles, it can be costly to keep it up. Being that my car has done 6000miles in the last 4 years and generally just sits around in the garage, I'm happy to leave the fully-synthentic in there for a year (or a year and a half so far!) whereas I'd change it every 6months if it were only mineral. Semi-synthetic's just cheap stuff really too, so I just used to change that when it looked murky!
nigel
Tick Over
Posts: 16
Joined: Wed Jul 14, 2010 12:24 pm
Location: Australia

Post by nigel »

Ok guys I do a bit of work on the BX when I can. I have a new clutch kit ready to go in. Ive done a lot of preliminary work researching the workshop manual and chatting to the local Citroen guru near where I live.

Im ready to now pull out the drive shafts and release the gear box from the engine. Yes I know I need to support the engine and gearbox. My only concern is the hydraulics. Ive been advised that I do not need to depressurise the Hydraulic system or disconnect any pipe/hoses. Just ensure that the accumalator and regulator are supportted and safely out of the way.

I really want this clutch replaced this weekend. Any advice appreciatted.
User avatar
Simran
4000 rpm
Posts: 424
Joined: Sat Aug 12, 2006 12:30 am
Location: leicester

Post by Simran »

Its so easy to release the pressure so i would do it anyway to be honest. Quarter to half turn of the bleed screw on the front of the regulator block thing and you should hear it hiss as iit bleeds the oil away back to the tank.

Reason being that if you disturb and crack or split the pipe between the pump and the block, you will get a nice coating of oil over everything under the bonnet and yourself. Ive had pipe from the accumulator to the valve block go on me twice and it takes ages to clean everything off and you dont want to be getting any oil on your new clutch after all the hard work. If you release the pressure and you get a leak, at least it will just be a little dribble.

Another tip is to stick the handbrake on and put a jack under your wishbone and something like an extension bar or block of wood between the strut top under the arch and the top of the hub if the bottom balljoints are spinning when you try to undo them to get the driveshafts out. It loads up the joint and makes it grip. Once the nut is off, take the block of wood out and put the jack under the brake disc and jack the strut up even further to help you lift it over the ball joint. Its hard to do it by hand because the anti roll bar makes it hard to wobble the wishbone about.

Good luck!
nigel
Tick Over
Posts: 16
Joined: Wed Jul 14, 2010 12:24 pm
Location: Australia

Post by nigel »

Ok guys Im stuck.

Right hand lower control arm came off easy with the help of a puller. LHD lower control arm wont budge.

Mechanic neighbour across the road had tried to lever it as it got hit with a hammer, still wwont budge. Have put Penetrene on it and will leave over night. Hopefully that will do the trick.

Considering heating it so as to expand the hole and hopefully it will pop out. Not keen at this stage as it will stuff up the rubber boots. Its got me stuffed and my Mechanic friend as well.

Any ideas folks? This is a show stopper and Im keen to get this clutch in.
User avatar
jayw
5000 rpm
Posts: 609
Joined: Mon Oct 30, 2006 3:31 pm
Location: Uranus

Post by jayw »

I assume you mean the arm will not seperate from the balljoint?

If that's the case, (and i do have to assume here the system's depressurised and the strut is phisically trying to retract it's weight up into the car), your best bet is to turn the steering giving you striking access to the wishbone, put a trolley jack under the the hub and jack the strut up (putting more splitting pressure against the joint). You should then find a couple of solid strikes (ideally with a copper hammer) on the exposed wishbone should see it "ping" down.

Never failed me.
Now listen here you mullet...
User avatar
Simran
4000 rpm
Posts: 424
Joined: Sat Aug 12, 2006 12:30 am
Location: leicester

Post by Simran »

^ second what jay said, the support underneath makes the difference, if you just hit it without, it just bounces about.
nigel
Tick Over
Posts: 16
Joined: Wed Jul 14, 2010 12:24 pm
Location: Australia

Post by nigel »

Thanks for all the good advice guys. Got the lower control arm off by hitting it from the front end instead of the back.

Its all slow progress as I fit in an hour or so when I can.
bxmark
3000 rpm
Posts: 175
Joined: Fri Oct 30, 2009 1:46 pm
Location: sheffield

Post by bxmark »

The valver looks well , I'm new to the forum but have had four valvers in the nineties , am on the look out for a nice one which is going to prove very hard , hope all the work goes well , I have fortunatly got a pal who used to work at a Citroen dealer and then a Citroen specialist so he knows the bx inside out , Mark
Post Reply