gimme more power!
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
gimme more power!
hey folks,
well finally got the ph1 out fot its first REAL RUN! and oh yeah im impressed! i went the edinburgh - loch lomond run 1 hour each way and it gets better, i was really surprised how much that motor picks up and runs, especially as i have the k+N on board with the full scorpion and the chip in. real rapid all the way up to 120mph i was well surprised to see it at 130mph and at only around 6500rpm????!!!! with 1250rpm to go! how far will it go?, i will be waiting a new belt before i find out i reakon it will go over 140 what do you guys think? well my car held up perfectly for the journey except when breaking hard once the abs light came on but a quick pit stop and re-start put it back off! apart from that the only other problem was the front number plat flew off somewhere by the way i have part of the run video'd on my mobile which i will try to get up, think its of the 130mph part
cheers rossco
well finally got the ph1 out fot its first REAL RUN! and oh yeah im impressed! i went the edinburgh - loch lomond run 1 hour each way and it gets better, i was really surprised how much that motor picks up and runs, especially as i have the k+N on board with the full scorpion and the chip in. real rapid all the way up to 120mph i was well surprised to see it at 130mph and at only around 6500rpm????!!!! with 1250rpm to go! how far will it go?, i will be waiting a new belt before i find out i reakon it will go over 140 what do you guys think? well my car held up perfectly for the journey except when breaking hard once the abs light came on but a quick pit stop and re-start put it back off! apart from that the only other problem was the front number plat flew off somewhere by the way i have part of the run video'd on my mobile which i will try to get up, think its of the 130mph part
cheers rossco
1989 BX 16v ph1 Big project chipped, k+N, scorpion s/s, weber throttle body, Nitrous injection
1990 BX 16v ph2 (now scrapped)
1990 BX 16v ph2 (now scrapped)
Seriously and no offence meant at all but I think you could end up with a pile of bits before long. We know how fast the engines are but trying to get that bit more out of them often results in failure. We see it enough on various forums including this one. Take it easy.
Prefer it to the Lamborghini, like Signor Gandini!
- Timmo
- Full Throttle
- Posts: 2233
- Joined: Tue Jun 27, 2006 3:30 pm
- Location: Cornwall! Tis where they make Oggy's!
- Contact:
not bad going rossco, but be a little weary! top speed is nigh on useless aroudn this country unless you happen to havea nice big airfeild to play with! and its a definate licenece looser too!
ive had mine at 140 ont he clock and 134 true on private land but have to say, tbh it means nothing!
ive had mine at 140 ont he clock and 134 true on private land but have to say, tbh it means nothing!
Timmo
After all i am the Cornish one!
Its Because its French!
Bx16v club - Sharing the love for the unloved!
After all i am the Cornish one!
Its Because its French!
Bx16v club - Sharing the love for the unloved!
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
hey well. yes there is plenty spaces around here for that, including kirknewton airfield, and hey why be a fan of something and be in a club if you cant share it and enjoy it! its not manditory for everyone to sit hard up against the wheel and drive at 27mph to tesco, we all enjoy something in common in different ways, and many of us enjoy caning it
cheers rossco
cheers rossco
1989 BX 16v ph1 Big project chipped, k+N, scorpion s/s, weber throttle body, Nitrous injection
1990 BX 16v ph2 (now scrapped)
1990 BX 16v ph2 (now scrapped)
- kriskarrera
- Tick Over
- Posts: 98
- Joined: Mon Sep 18, 2006 9:54 pm
- Location: Wiltshire
- docchevron1472
- 4000 rpm
- Posts: 336
- Joined: Tue Aug 22, 2006 10:53 am
- Location: The End of the World
- Contact:
Re: gimme more power!
Your ECU is chipped??thanuttiscotsman wrote: i was well surprised to see it at 130mph and at only around 6500rpm????!!!! with 1250rpm to go!
Standard limiter is 7200rpm.
You obviousley achieved these speeds on private tracks, not the public highway, so thats fine, enjoy.
But get the belt changed!
1990 BX 16v Phase 2
1989 BX TD hybrid
1971 BL 350FG Ambulance (unique)
1993 Dennis Lance 132
That's when I reach for my Revolver
1989 BX TD hybrid
1971 BL 350FG Ambulance (unique)
1993 Dennis Lance 132
That's when I reach for my Revolver
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
hi there,
yeah the ecu is chipped, will go to 7800rpm. i do actually have a belt for it just not got it on yet! also i know the car was well maintained in the past as it was owned by a mechanic before it was in the club. but yeah great fun for £350.
rossco
yeah the ecu is chipped, will go to 7800rpm. i do actually have a belt for it just not got it on yet! also i know the car was well maintained in the past as it was owned by a mechanic before it was in the club. but yeah great fun for £350.
rossco
1989 BX 16v ph1 Big project chipped, k+N, scorpion s/s, weber throttle body, Nitrous injection
1990 BX 16v ph2 (now scrapped)
1990 BX 16v ph2 (now scrapped)
The speedos are quite far out in some cars. I once hit the limiter in 5th gear several years ago, which I'm told can only be 143mph (with std box, limiter and wheels etc) but the speedo had gone past the "H"
Mines now chipped among other things, yet ironically I definately wouldn't put the engine through it again. I know my rev counter isn't accurate, but it won't pull cleanly to it's new limiter (7800rpm) so I'd be putting it through alot of needless pain. I think it dies off at about 7500rpm or there abouts, hard to tell really.....the rev counters like the oil pressure gauge. Its there for amusement.
Mines now chipped among other things, yet ironically I definately wouldn't put the engine through it again. I know my rev counter isn't accurate, but it won't pull cleanly to it's new limiter (7800rpm) so I'd be putting it through alot of needless pain. I think it dies off at about 7500rpm or there abouts, hard to tell really.....the rev counters like the oil pressure gauge. Its there for amusement.
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
Kitch wrote: I think it dies off at about 7500rpm or there abouts, hard to tell really.....the rev counters like the oil pressure gauge. Its there for amusement.
hey man,
yeah? mines pulls like a concord from 4.5k with points from there to the limit where it feels like its boosting a certain points. from 5.5k up to the limit mine runs like a cheetah on spee*! which im glad and well proud of! only flat point is from 3.3k rpm to 4k it just goes eh what? driving? go faster? eh? then it hits 4k and goes ppppprrrrrrrrnnnnneeeeeeeeeeeoooooowwwwwww aaarrrggghhh i love it sooooo much
cheers rossco
1989 BX 16v ph1 Big project chipped, k+N, scorpion s/s, weber throttle body, Nitrous injection
1990 BX 16v ph2 (now scrapped)
1990 BX 16v ph2 (now scrapped)
-
- Tick Over
- Posts: 85
- Joined: Mon Aug 14, 2006 11:11 pm
- Location: W London
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
Channel Hopper wrote:Welcome to the budget supercar arena, Top Gear should have a spot each week on this type of vehicle.thanuttiscotsman wrote: but yeah great fun for £350.
yeah well i'd be happy to knock up a few videos!, like every week
1989 BX 16v ph1 Big project chipped, k+N, scorpion s/s, weber throttle body, Nitrous injection
1990 BX 16v ph2 (now scrapped)
1990 BX 16v ph2 (now scrapped)
-
- 4000 rpm
- Posts: 281
- Joined: Wed Aug 02, 2006 7:16 pm
- Location: South Bucks, England
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
power
I am with Kitch - it is doubtfull you will be making decent power over 7500 and std components such as rod bolts and tappets start to get into a grey area as far as reliability is concerned at around 7700/7800.
My shift point is set at 7500 and limiter at 8k but it pays to use the shift point as the limiter the hard cut is 8k - car ha sbeen there once but that was an error on a RR day but it did make power all the way
Cheers
Luke
My shift point is set at 7500 and limiter at 8k but it pays to use the shift point as the limiter the hard cut is 8k - car ha sbeen there once but that was an error on a RR day but it did make power all the way
Cheers
Luke
Please call me Luke
1989 BX 16valve White 70k almost up to scratch
1989 BX 16valve White 70k almost up to scratch