is anybody have the L shape protector?
I'm living in Taiwan...
thank you!
MK2 a pair of rear bumper L shape protect line wanted!
MK2 a pair of rear bumper L shape protect line wanted!
I like Citroen so much.Now I have a BX TZi and BX 19 GTi...and had convertted TZi to GTi 16V... It's wonderful !
Hello, I still wait for your news....NZ16v wrote:sounds fine. out of interest, what colour do you want? its just i can tinit the material to semi-match the car etc, so chips dont stand out so much.
I like Citroen so much.Now I have a BX TZi and BX 19 GTi...and had convertted TZi to GTi 16V... It's wonderful !
Sorry mate, have to organise making em up-they will be white, you can put them in boiling water to soften them slightly- you will need to do this, as the tail lights always sit a little differently either side! And then fit to car using urethane glue, or screws.
Will be in touch as soon as they are ready, and will find out shipping costs- could you PM your address, so i can get some prices? It wont be very much , but want to let you know!
Will be in touch as soon as they are ready, and will find out shipping costs- could you PM your address, so i can get some prices? It wont be very much , but want to let you know!
Would rather be driving ONE 16v,than fixng TWO.
if i can get a few people interested, it would be much more worth my while-i will get onto the ones you asked for icrc i promise!!
Would definitely do em in pairs, the mold is made that way, so might as well. they will either be fibreglass bog, or cc60 rigid urethane-you can glue em to the bumpers with sika/silcone/urethane etc, but may need sitting in boiling water to get em to fit to your personal vehicle-i had to, and they were off the same car!
Would definitely do em in pairs, the mold is made that way, so might as well. they will either be fibreglass bog, or cc60 rigid urethane-you can glue em to the bumpers with sika/silcone/urethane etc, but may need sitting in boiling water to get em to fit to your personal vehicle-i had to, and they were off the same car!
Would rather be driving ONE 16v,than fixng TWO.
hello, NZ16v...NZ16v wrote:if i can get a few people interested, it would be much more worth my while-i will get onto the ones you asked for icrc i promise!!
Would definitely do em in pairs, the mold is made that way, so might as well. they will either be fibreglass bog, or cc60 rigid urethane-you can glue em to the bumpers with sika/silcone/urethane etc, but may need sitting in boiling water to get em to fit to your personal vehicle-i had to, and they were off the same car!
how about the protector?
I still wait for them......
thanks
I like Citroen so much.Now I have a BX TZi and BX 19 GTi...and had convertted TZi to GTi 16V... It's wonderful !
UPDATE-see for sale thread too.
I have made up 4 sets!
They are hard urethane-CC60- and will need sanding and painting-they are urethane, so heat them in boiling water, fit them, then take em off and paint em.
For my set i just lined em up in the right spot, marked it, then siliconed them on- for where they are, they dont need screws. Unless you have the holes there already, which is fine, the urethane takes self tappers fine!
I have made up 4 sets!
They are hard urethane-CC60- and will need sanding and painting-they are urethane, so heat them in boiling water, fit them, then take em off and paint em.
For my set i just lined em up in the right spot, marked it, then siliconed them on- for where they are, they dont need screws. Unless you have the holes there already, which is fine, the urethane takes self tappers fine!
Would rather be driving ONE 16v,than fixng TWO.