CO adjusting problem.
CO adjusting problem.
I have a problem in my 16V.
I just cant adjust the CO level. The level is always to high (about the 3.x).
Other problem is that sometimes the engine dies if i do not keep some aceleration in the pedal.
I have replaced the sparks and also the engine temperature sensor, but the problem maintains.
Anyone makes an ideia of what could be causing this?
I just cant adjust the CO level. The level is always to high (about the 3.x).
Other problem is that sometimes the engine dies if i do not keep some aceleration in the pedal.
I have replaced the sparks and also the engine temperature sensor, but the problem maintains.
Anyone makes an ideia of what could be causing this?
91' Citroën BX GTi 16v
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
hi there,
i used to have this problem with my car. what you need to do is adjust the afm via the spring flap tension. i think from memory that if you put more tension on the spring that weakens the fuel mixture and less tension gives a ritcher mixture.
cheers rossco
i used to have this problem with my car. what you need to do is adjust the afm via the spring flap tension. i think from memory that if you put more tension on the spring that weakens the fuel mixture and less tension gives a ritcher mixture.
cheers rossco
1989 BX 16v ph1 Big project chipped, k+N, scorpion s/s, weber throttle body, Nitrous injection
1990 BX 16v ph2 (now scrapped)
1990 BX 16v ph2 (now scrapped)
- kriskarrera
- Tick Over
- Posts: 98
- Joined: Mon Sep 18, 2006 9:54 pm
- Location: Wiltshire
CO
IF you can't adjust the co via the AFM and you have idling issues I would try and get a substitute AFM to try.
Cheers
Luke
Cheers
Luke
Please call me Luke
1989 BX 16valve White 70k almost up to scratch
1989 BX 16valve White 70k almost up to scratch
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
hi there,
listen make sure you have tried adjusting it properly. firstly the screw on the side of the afm anticlockwise weakens the fuel mix on tickover and clockwise strengthens the mix.
inside the the afm you can adjust the running (not idle) fuel mixture. tighten the flap spring to get more fuel and loosen it for less i think. if this doesnt solve it then does your car idle high? if so it may be running on choke (so to speak) all the time hence the rich mix.
cheers rossco
listen make sure you have tried adjusting it properly. firstly the screw on the side of the afm anticlockwise weakens the fuel mix on tickover and clockwise strengthens the mix.
inside the the afm you can adjust the running (not idle) fuel mixture. tighten the flap spring to get more fuel and loosen it for less i think. if this doesnt solve it then does your car idle high? if so it may be running on choke (so to speak) all the time hence the rich mix.
cheers rossco
1989 BX 16v ph1 Big project chipped, k+N, scorpion s/s, weber throttle body, Nitrous injection
1990 BX 16v ph2 (now scrapped)
1990 BX 16v ph2 (now scrapped)
- kriskarrera
- Tick Over
- Posts: 98
- Joined: Mon Sep 18, 2006 9:54 pm
- Location: Wiltshire
- thanuttiscotsman
- 7000 rpm
- Posts: 1137
- Joined: Sun Aug 13, 2006 8:16 am
- Location: Scotland
hi there,
an easy way to check the fuel pressure regulator is to take the return fuel pipe off the top of it and turn the car over a couple times. you should get a spray about 6-10 inches into the air above the engine. if there is no spray then that is a problem. just make sure you have a towel ready to catch the fuel when you do this so it doesnt land on the coil etc.
cheers rossco
an easy way to check the fuel pressure regulator is to take the return fuel pipe off the top of it and turn the car over a couple times. you should get a spray about 6-10 inches into the air above the engine. if there is no spray then that is a problem. just make sure you have a towel ready to catch the fuel when you do this so it doesnt land on the coil etc.
cheers rossco
1989 BX 16v ph1 Big project chipped, k+N, scorpion s/s, weber throttle body, Nitrous injection
1990 BX 16v ph2 (now scrapped)
1990 BX 16v ph2 (now scrapped)
RE. idle problem: my 16v used to cut out after a hot start. However, if after starting, I revved engine and held RPM at about 5,000 RPM (ouch) it would idle perfectly until I stopped again. A good clean out of idle circuit passage and a new AFM cured it. I think the problem was the flap sticking, and the revving moved the flap beyond the sticky region.
over fuelling
I would check the fuel pressure with a guage also worth checking the vacuum pipe from the inlet manifold to the underside of the regulator as they often get blocked or damaged causing idling issues.
If the fuel pressure is correct and the AFM and ICV are all in good order it is likely that the ecu is causing the over fuelling so would suspect faulty temp sensors feeding the ecu lies.
Cheers
Luke
If the fuel pressure is correct and the AFM and ICV are all in good order it is likely that the ecu is causing the over fuelling so would suspect faulty temp sensors feeding the ecu lies.
Cheers
Luke
Please call me Luke
1989 BX 16valve White 70k almost up to scratch
1989 BX 16valve White 70k almost up to scratch
Thanks to all for the replyes.
In the Citroen dealer they told me that i have an electrical problem somewhere in the ingnition circuit wich results in excessive fuel in the injectors.
The problem seems to be between the 2 red points in the image:
http://img249.imageshack.us/img249/3482/probxo9.jpg
They tested my car using another idle control valve, and another AFM from a good working car, and i also replaced the water temp sensor, but the problem continues.
It may possible be the ECU broken. It only happens sometimes, and when it does, i hear some strange "tick tick" noise when i turn the key to start the ignition of the engine.
In the Citroen dealer they told me that i have an electrical problem somewhere in the ingnition circuit wich results in excessive fuel in the injectors.
The problem seems to be between the 2 red points in the image:
http://img249.imageshack.us/img249/3482/probxo9.jpg
They tested my car using another idle control valve, and another AFM from a good working car, and i also replaced the water temp sensor, but the problem continues.
It may possible be the ECU broken. It only happens sometimes, and when it does, i hear some strange "tick tick" noise when i turn the key to start the ignition of the engine.
91' Citroën BX GTi 16v
tick tick
Can you tell where the noise is coming from i.e. front or rear of the car?
I would have the injector thoroughly tested and cleaned as they may well not be shutting off properly or leaking when they should be fully closed.
I think Alan S has had similar issues.
Cheers
Luke
I would have the injector thoroughly tested and cleaned as they may well not be shutting off properly or leaking when they should be fully closed.
I think Alan S has had similar issues.
Cheers
Luke
Please call me Luke
1989 BX 16valve White 70k almost up to scratch
1989 BX 16valve White 70k almost up to scratch
Re: tick tick
The noise comes from the front and the back of the car.Toddman wrote:Can you tell where the noise is coming from i.e. front or rear of the car?
I would have the injector thoroughly tested and cleaned as they may well not be shutting off properly or leaking when they should be fully closed.
I think Alan S has had similar issues.
Cheers
Luke
In the front comes from the idle control valve, and also from a relay near the LHM deposit. In the back of the car i dont know exactly from, but i think it is from the bosch fuel component in the side of the fuel filter.
It seems the entire ignition circuit is being afected.
The problem is not from the injectors because my car is also working with LPG, with independent LPG injectors, and the problem is the same while runing in both type of fuel.
91' Citroën BX GTi 16v