MK2 a pair of rear bumper L shape protect line wanted!
Posted: Wed Aug 25, 2010 2:26 pm
is anybody have the L shape protector?
I'm living in Taiwan...
thank you!
I'm living in Taiwan...
thank you!
BX16V.com Forum
The home of the BX16V.com Forum
http://www.bx16v.com/phpBB3/
MK2 a pair of rear bumper L shape protect line wanted!
Page 1 of 1
Posted: Tue Aug 31, 2010 11:59 pm
yes, i have had a set molded. How many you want, how much wanna pay!
Posted: Wed Sep 01, 2010 2:58 pm
how about £10?
for sure, I show the L shape protetor I meant(point in picture)...
forward you reply...
for sure, I show the L shape protetor I meant(point in picture)...
forward you reply...
Posted: Wed Sep 01, 2010 8:53 pm
sounds fine. out of interest, what colour do you want? its just i can tinit the material to semi-match the car etc, so chips dont stand out so much.
Posted: Wed Sep 01, 2010 11:15 pm
it sound pretty good!I need white ones...just like my car...
when you ready to send, tell me you paypal and I'll finish the payment...
ok?
thank you!
when you ready to send, tell me you paypal and I'll finish the payment...
ok?
thank you!
Posted: Sat Sep 11, 2010 3:11 pm
Hello, I still wait for your news....NZ16v wrote:sounds fine. out of interest, what colour do you want? its just i can tinit the material to semi-match the car etc, so chips dont stand out so much.
Posted: Sun Sep 12, 2010 8:20 am
Sorry mate, have to organise making em up-they will be white, you can put them in boiling water to soften them slightly- you will need to do this, as the tail lights always sit a little differently either side! And then fit to car using urethane glue, or screws.
Will be in touch as soon as they are ready, and will find out shipping costs- could you PM your address, so i can get some prices? It wont be very much , but want to let you know!
Will be in touch as soon as they are ready, and will find out shipping costs- could you PM your address, so i can get some prices? It wont be very much , but want to let you know!
Posted: Fri Sep 24, 2010 8:13 pm
Is your set a single one? Or do you go onto series?
I ask because of being interested, too. And there are certainly some more interested folks.
Jones
I ask because of being interested, too. And there are certainly some more interested folks.
Jones
Posted: Sat Sep 25, 2010 9:34 am
if i can get a few people interested, it would be much more worth my while-i will get onto the ones you asked for icrc i promise!!
Would definitely do em in pairs, the mold is made that way, so might as well. they will either be fibreglass bog, or cc60 rigid urethane-you can glue em to the bumpers with sika/silcone/urethane etc, but may need sitting in boiling water to get em to fit to your personal vehicle-i had to, and they were off the same car!
Would definitely do em in pairs, the mold is made that way, so might as well. they will either be fibreglass bog, or cc60 rigid urethane-you can glue em to the bumpers with sika/silcone/urethane etc, but may need sitting in boiling water to get em to fit to your personal vehicle-i had to, and they were off the same car!
Posted: Tue Oct 05, 2010 1:37 pm
hello, NZ16v...NZ16v wrote:if i can get a few people interested, it would be much more worth my while-i will get onto the ones you asked for icrc i promise!!
Would definitely do em in pairs, the mold is made that way, so might as well. they will either be fibreglass bog, or cc60 rigid urethane-you can glue em to the bumpers with sika/silcone/urethane etc, but may need sitting in boiling water to get em to fit to your personal vehicle-i had to, and they were off the same car!
how about the protector?
I still wait for them......
thanks
Posted: Mon Nov 01, 2010 7:52 pm
UPDATE-see for sale thread too.
I have made up 4 sets!
They are hard urethane-CC60- and will need sanding and painting-they are urethane, so heat them in boiling water, fit them, then take em off and paint em.
For my set i just lined em up in the right spot, marked it, then siliconed them on- for where they are, they dont need screws. Unless you have the holes there already, which is fine, the urethane takes self tappers fine!
I have made up 4 sets!
They are hard urethane-CC60- and will need sanding and painting-they are urethane, so heat them in boiling water, fit them, then take em off and paint em.
For my set i just lined em up in the right spot, marked it, then siliconed them on- for where they are, they dont need screws. Unless you have the holes there already, which is fine, the urethane takes self tappers fine!