I saw something about it on the old forum. I think it was the newer ES typ V6, not the older ZPJ.
Anyone knows about a successful conversion, pics would be nice
it is possible by all accounts but have never seen one!! afaik the back of the block needs to be ground down to allow it to fit properly,
have seen a couple of v6 conversions done on 205's and 309's, the engine isnt that much heavier than the mi either,
would make a blinding conversion though!
Timmo
After all i am the Cornish one!
Its Because its French!
Bx16v club - Sharing the love for the unloved!
I think BX has a smaller engine bay than 205 and 309. I have some friends driving 205 Mi16 and they have more clearance behind the engine compared to BX.
Too much torque? Not in my world Power is something you never can get too much of
There is a 405 Mi16 with turbo here running 550hp, and a 205 Mi16 turbo with about 350hp. The 205 only drives dragracing but the 405 is used on the road.
I have an old XM with V6, but i dont think its possible to fit it in the BX without cutting it up everywhere...
normal m.i. conversions into 205's will use a reangled exhaust manifold leading to it looking like there is more room in there! but the205 engine bay is the smaller of the 3 without doubt! (hence why the std inlet on the m.i. sits under the slam panel on a 205!! and is tight on a 309 yet int he bx has a couple of inches!!!)
Timmo
After all i am the Cornish one!
Its Because its French!
Bx16v club - Sharing the love for the unloved!
I have an old XM with V6, but i dont think its possible to fit it in the BX without cutting it up everywhere...
This does fit into a Bx engine bay, as I've tried it myself
I wish I'd taken a picture but sadly I didn't. Decided not to do the conversion as from memory the lower front rail fouls, mount centres are diffferent across the engine and the rear bay fire wall would have to be cut out.
Have still got the V6 24v engine, box and loom in a friends garage, probably waiting for a Peugeot 505 GTi to turn up.
Mike P.
Founder member of the Phase 1 Appreciation Society!
- - - - -
'88 'F' White Bx16v - 62k miles & as seen on TV
Tim - the common route is via a supercharger such as one from the new cooper, ideally you would need an emerald management to control everything so I reckon just under a grand would see you with a decent reliable supercharged mi powered BX should run at about 220-250 BHP quite happily.
Cheers
Luke
Please call me Luke
1989 BX 16valve White 70k almost up to scratch
Toddman wrote:Tim - the common route is via a supercharger such as one from the new cooper, ideally you would need an emerald management to control everything so I reckon just under a grand would see you with a decent reliable supercharged mi powered BX should run at about 220-250 BHP quite happily.
Cheers
Luke
Superchargers are a bit expensive, otherwise i had bought one. Preferably a Rotrex then.
Used turbos from Saabs are cheap, almost for free.
I have turbo, IC, extra fuel system already. Probably rolling with turbo 2007!
Over 200hp the clutch has to be replaced too, expensive stuff
Wasn't someone on here going to fit a supercharger, was it Keith Adams?
Even if you 'only' had a 60BHP increase, that's a hell of an increase per pound.
Dan
We did look into it Dan.
A good mod is to use 8v pistons to lower the CR and mini chargers are quite cheap now the emerald weighs in at about £450 so all can be done within budget I reckon if oyu are capable.
Cheers
Luke
Please call me Luke
1989 BX 16valve White 70k almost up to scratch